Tiptop Buchla Model 245t Sequential Voltage Source Eurorack Module (30 HP)
at B&H Photo Video
About this item
Create vibrant sequences with the Tiptop Audio Buchla 245t Sequential Voltage Source, a 4-channel 5-step sequencer in Eurorack format. The sequencer is driven by an internal clock, the Pulser, which has controls for frequency and pulse width. There is also voltage control and triggers with buttons to start or stop the clock.
Pulser Section
Pulse: Output generates a pulse with a 10V initial stage that lasts for 0.1 ms followed by a 5V gate stage length determined by the Pulse Length control.
Ref: Outputs a ramp wave that descends from 10 to 0V at the rate of the Pulser.
Pulse Length: Sets the length of the 5V stage of the pulse from 0 to 100% of the duty cycle. External CV control is added to the knob setting.
Internal Time: Controls the period of the Pulser output from 10 seconds (full CW) to a few milliseconds (full CCW). External CV has an attenuverted control to either add (CW) or subtract (CCW) external voltage from the knob setting. External CV can increase the maximum and minimum period of the pulser to approximately 50 seconds to 1 ms (1 kHz)
Start: Pressing this button generates a pulse and reference ramp at those outputs. A pulse on the Start input also begins Pulser generation.
Stop: Pressing the button or sending a pulse to the input jack stops the Pulser if already running. Additional presses or pulses to the Stop input will manually trigger a single pulse output from the Pulser.
Stored Voltage Stages
Advance In: Accepts a pulse from the Pulser or external source (281t EOC for example) and each pulse advances to the next stage from 1 to 5. The switches in the Stage Select section can control the number of stages played back.
Stage Gate Output: Each stage has a dedicated gate output that produces a high voltage (10V) when that stage is active. This gate can be used to trigger events like envelopes.
Out: The voltage output of the current active stage. Each of the outputs has an independent voltage.
Stored Voltages: 4 rows of 5 locations of stored analog voltages set by a control knob.
Analog (In): CV input (0 to 10V) that addresses the stages. When the voltage is above the O range the Analog input is active and the Advance and Stage Select Inputs are disabled.
Ranges are approximately:Off (0 to 0.75V)Stage 1 (0.75 to 2.5V)Stage 2 (2.5 to 4.25V)Stage 3 (4.25 to 6V)Stage 4 (6 to 7.75V)Stage 5 (7.75 to 10V)
Off (0 to 0.75V)
Stage 1 (0.75 to 2.5V)
Stage 2 (2.5 to 4.25V)
Stage 3 (4.25 to 6V)
Stage 4 (6 to 7.75V)
Stage 5 (7.75 to 10V)
Stage Select Inputs: Pulses on these 5 inputs will immediately set the active Stage to the corresponding input. Using these inputs can create a type of analog preset memory for 4 CV settings in your modular system.
Stage Switches: These 4 switches enable or disable the stage transitions. Switch 1 controls Stage 1 to 2 transition, switch 2 controls Stage 2 to 3, and so on. By disabling a stage transition, the length of the sequence can be shortened or captured.
Eurorack Ready
30 HP Eurorack format module
Maximum depth: 1" (25mm)
Includes power ribbon cable with Eurorack power headers
Power consumption: +12V: 63mA, -12V: 28mA
- Features
- Pulser Section Generates Control Pulse
- Drives Sequential Stored Voltages
- 5 Stages with 4 Voltages per Stage
- Includes Ribbon Power Cable
Specifications
- Sound Generation
Analog
- Audio I/O
No
- MIDI I/O
No
- CV/Gate I/O
8x 1/8" / 3.5 mm TS CV Input6x 1/8" / 3.5 mm TS Gate Output5x 1/8" / 3.5 mm TS CV Output
- Patch Points
10x 1/8" / 3.5 mm TS Input9x 1/8" / 3.5 mm TS Output
- Eurorack Current Consumption
63 mA on +12 V Rail28 mA on -12 V Rail
- Horizontal Pitch
30 HP
- Synth Type
Eurorack Module
- Expression Controls
No
- Number of Pads
No
- Built-In Speaker
No
- Oscillators
No
- Mixer
No
- Amplifiers
No
- Envelopes
No
- Filters
No
- Sequencer
Yes
- Arpeggiator
No
- Sync I/O
2x 1/8" / 3.5 mm TS Clock Output
- Power Requirements
Eurorack Power
- Included Accessories
No
- Package Weight
1.035 lb
- Box Dimensions (LxWxH)
7 x 6.1 x 2.3"