Ashly FX60.8 Multipurpose Installation Network Amplifier with DSP (1 RU, 1/2 Rack)

Save time, space, and money on your next audio amplifier installation with the Ashly FX60.8, a multipurpose installation amplifier with integrated DSP and a built-in WAP hotspot for simple connection and configuration via Wi-Fi as well as an intuitive web-based software UI. The amplifier also features an Ethernet connection for wired LAN connections—no network router required.

At a Glance

Low (4/8 ohms and 25V) or hi-impedance (70/100V) operation, selectable in software

Balanced Mic/Line inputs on removable Euroblock connectors, plus unbalanced RCA inputs

2-channel SPDIF digital IO

Front-panel status LEDs for amp, input, output, and network

Advanced Dynamic Power Sharing distributes power between channels

Networkable via Ethernet or built-in Wi-Fi

Built-in advanced DSP on all inputs and outputs including: Sensitivity, Routing, Gain, PEQ, Compressor, Limiter, FIR filters, X-over, Polarity, and Delay

Browser-based UI accessed via PC or mobile device—no software to install.

8 input channels x 8 output channels

Auto/Manual Power Saver Mode (sleep/standby), adjustable in software

Customized speaker presets may be created, saved, and loaded for each output channel

Addressable GPIO, Standby/Mute, and VC remote ports. VC assignable per channel via software

Highly efficient Class-D circuitry and lightweight

Includes rack mount ears

Intelligent DSP

Powerful DSP engine that can be configured to suit a wide range of tasks without the need for additional equipment. From processing input sources, routing, and output DSP that can fine tune the sound of any speaker. Everything you need is right there. These can route into Zones A-H and then into the four outputs.

Input processing

Zone processing

Output processing

Speaker processing

Device settings

Multi-zone music distribution for retail and restaurant/bar

Noise masking for offices and medical facilities

Media playback for hotel lobbies, retail, and museum kiosks

Mobile sound

Dashboard: status display, level control, and metering for Zones A-H

Inputs: Gain/Trim, Sensitivity

Zones: source select, mono/stereo, level control, and metering as well as GPIO assignment and Compressor for Zones A-H

Outputs: Routing (from Zones A-H), Delay (up to 100ms), 10-bands of fully parametric EQ for outputs 1 through 4

Speaker presets: Save/Load/Select from Library, Custom: X-over and Gain, 11-band speaker EQ (fully parametric), FIR filter import, Speaker alignment delay (up to 10ms), Polarity, Limiter (Clip, Peak, and RMS), and Output mode (Low/Hi-Z)

Settings: System and Device info, Backup and Restore, Speaker Preset Library, Power Management (standby/sleep, auto/manual), GPIO settings, LAN, and Wi-Fi

Intuitive Software UI

To control FX’s powerful DSP, you’ll find its user-friendly software interface that offers an intuitive workflow and easy access to FX’s most advanced functions. A webpage-like directory on the left-hand side of the UI keeps all necessary functions clearly visible and accessible at all times. No multi-page layering, no right-click or hidden menus, and no getting “lost in the weeds”.

FX Dashboard: Quickly see the amp’s status displayed, along with Zone controls. The directory then takes you through the signal flow from Inputs to Zones to Outputs, followed by general settings—easy and simple.

Create, save, and load speaker presets to accommodate virtually any loudspeaker. These can be loaded independently per channel, so different speakers may be used for different zones, or satellites and subs may be used for a bar or auditorium.

The FX UI screens are well laid out, with consistent controls from page to page that are informative and easy to read. All device information and operations are at your fingertips. From input / output settings and remote assignments to power and IP.

Wireless Access

Rather than being tethered to a PC with an installed app, FX can be accessed anytime, anywhere with almost any browser-enabled device. FX software provides easy viewing and control from virtually any PC, tablet, or smartphone, regardless of OS. No software to install (it’s built into the FX unit). Just connect using the Ethernet port or built-in Wi-Fi and you’re ready to rock & roll. The Wi-Fi connection allows secure ID and password protection from unauthorized use and for more advanced users, Ethernet allows custom IP settings for use on a more complex wired LAN.

The browser-based network interface also makes remote service and troubleshooting easier. A technician can simply log in with remote access from their PC or mobile device and without needing to download or install any software.

Built-in Wi-Fi hotspot for directly connecting to an FX amp:Connect from any PC or mobile device with a browserPeer-to-peer connectivity. No additional network hardware neededSimply find FX on your device as an “available” network and selectLog in using secure WEP ID/PWYou’re connected

Connect from any PC or mobile device with a browser

Peer-to-peer connectivity. No additional network hardware needed

Simply find FX on your device as an “available” network and select

Log in using secure WEP ID/PW

You’re connected

Get even more functionality with a router/gateway:You can also set an FX unit as a client for use with a DHCP routerRemote access to on-site units for service and troubleshootingEasier management of multiple units in a systemAccess to software updates and preset library downloadsFX may also be used on a wired LAN with either a DHCP or static IP address

You can also set an FX unit as a client for use with a DHCP router

Remote access to on-site units for service and troubleshooting

Easier management of multiple units in a system

Access to software updates and preset library downloads

FX may also be used on a wired LAN with either a DHCP or static IP address

Flexible Amp Modes

FX can change gears to work for whatever type of speakers your system requires. Its multi-mode operation with switchable Low-Z (4/8 ohms & 25V) or Hi-Z (70/100V) can be selected in software, so you can mix and match speaker types as needed. The amplifier also offers convenient power-sharing technology that balances power between channels to meet different load requirements.

Each channel of the amplifier can operate at Low-Z mode or be bridged for 70/100V constant voltage output by selecting the appropriate output mode in the DSP software on each channel.

The SPDIF digital I/O may be used to connect other compatible equipment or may be used to bridge two FX amplifiers and digitally expand the system.